This particular rewire stemmed from another Angies List Customer calling in to get his 1920's Knob and Tube wiring looked at. The home is located in West Seattle. The process for the home inspection begins with taking off all of the wall plates. Most Electrical contractors will only use a plug checker to determine the extent of the knob and tube, not Seatown Electric. Our process is very thorough and accurate, leaving all of our customers with a detailed report of how much of the home is knob and tube, and what condition it is in. We have a 24hr turnaround process for all of our estimates, so the bid process does not drag out.
After a few back and forth e-mails confirming scope of work and misc. additional items, the homeowner let us know that we where the middle bid. Our price for the rewire was not too high and not too low. We scheduled the work for 5 total working days.
The house was vacant during the rewire (this is not required) but does help. There are many different Wiring Methods, but after many rewires, we believe we have found the best most efficient way to do them. On day one, we focus on pulling out all of the old switches and outlets. We aren't concerned with keeping the old outlets since they aren't Tamper Resistant which is required in the 2014 NEC Code. Not every single outlet is required to be Tamper Resistant, but enough for Seatown Electric to make it a company policy that all outlets will be Tamper Resistant.
Once the outlets and switches are removed, the next step is to remove all of the old metal boxes. This home had lath and plaster, so we had to be very careful not to knock out pieces of the wall. Using a flat head screw driver we disassemble and pry out the old boxes. Then cut out the opening for the new Plastic Cut In Box. After all the new boxes are cut out, we vacuum up all of the lath and plaster pieces and shake off the drop clothes in the trash, to get ready for the next steps.
Getting all of the boxes out and removing the knob and tube will take up most of day one. On day two, home run wires are pulled. Home runs are the start of the new circuit. Basically, they come from
the electrical panel to the start of the circuit. Once they are all pulled in, we start fishing wires in to all of the new electrical box locations. NMB Wiring is used for all of the new electrical installed. The next few days we are fishing in the new circuits.
Seattle Electrical Code only requires you to rewire the dwelling "as is" meaning you only need to rewire to the existing locations. Labor and Industries will sometimes make you rewire "up to NEC Code" meaning you have to add outlets and switches. This adds a minimum of 3-5 days. Since the home was in Seattle territory, we only added outlets that the homeowner requested.
On the last day of the rewire the circuits are all attached to the Electrical panel. This homeowner chose to purchase the best Electrical Panel we offer. It comes with a copper bussing, whole home surge protection, updated grounding and bonding, panel labeling, and limited lifetime warranty on all parts.
A thorough testing of all the circuits is done after power is restored to the home. Everything worked perfect the first time. Inspection was scheduled the next day, and passed off the first time. This whole home rewire went about as smooth as it could have. Another satisfied Angies List customer.
Showing posts with label electrical panel. Show all posts
Showing posts with label electrical panel. Show all posts
Tuesday, March 17, 2015
Monday, March 16, 2015
Emergeny Electrical Service Redmond Washington
SeaTown Electric received another emergency service call today. It was for a customer who found us through Angie's List . The customer lives in Redmond Washington, and the emergency crew for SeaTown Electric was just wrapping up a Knob and Tube rewire inspection in Seattle Washington. The home owner had a sump pump that had no power to it. The arrival time was within 2 hours from the home owner calling in. Our crew showed up ready to troubleshoot all of their electrical needs. It started by inspecting the outlet that was not working. Usually during electrical troubleshooting we look for space heaters, vacuums, tripped GFCI outlets, or any other "heavy" electrical load that could effect the circuit. After taking out multiple electrical outlets, and inspecting the wiring, everything looked good. The electrical panel was the next step to look over.
At the electrical panel we noticed loose wires on the neutral bar, But the wires did not connect to the circuit that was not working. After opening more outlets in the circuit and tracing more wires, we found a junction box. There was the issue, the wires in the junction box where loose. after a quick tighten, the outlets all worked again. the electrician notified the home owner that Seattle, Bellevue, Redmond, Kirkland, Basically all King and Snohomish county requires GFCI outlets in exposed basements, and that there sump pump outlet was not GFCI protected.
The home owner decided to GFCI protect the sump pump outlet and everything was brought up to Washington State code and NEC code. The Redmond electrical job was complete. Another Angie's List satisfied customer.
At the electrical panel we noticed loose wires on the neutral bar, But the wires did not connect to the circuit that was not working. After opening more outlets in the circuit and tracing more wires, we found a junction box. There was the issue, the wires in the junction box where loose. after a quick tighten, the outlets all worked again. the electrician notified the home owner that Seattle, Bellevue, Redmond, Kirkland, Basically all King and Snohomish county requires GFCI outlets in exposed basements, and that there sump pump outlet was not GFCI protected.
The home owner decided to GFCI protect the sump pump outlet and everything was brought up to Washington State code and NEC code. The Redmond electrical job was complete. Another Angie's List satisfied customer.
Wednesday, February 25, 2015
Is My Electrical Panel Safe?
Our answer is always the same. What year was the house built? And, have you ever had it inspected? If it has been 5-10 years, and you have no record of any inspections, you owe it to yourself and family, to have it looked at.
Along with inspections, to assure your safety, there are also websites available to help rule out problem panels. www.ismypanelsafe.com is a a very helpful recource, to help determine if your panel is one of the worst out there. In the electrical industry, there are three panels that every electrical contractor will agree are the worst: Zinsco panels, Federal Pacific panels, and of course, Fuse panels. All of which, have been recalled due to extreme fire hazards.
Electrical panels are the heart of your electrical system, and a lot of the time, are overlooked as being a simple "grey box". In reality, the panel is the source that ties in all of the components, that make your system safe. If you constantly trip breakers, and your panel is older than 20 years, you need to start thinking about upgrades.
To request a FREE quote, visit us at www.SeaTownElectric.com
Subscribe to:
Posts (Atom)
